This state-of-the-art wood warming waterborne floor sealer and primer is formulated to enhance the natural appearance and grain of all types of wooden flooring. Use before overcoating with induro® XL1, XL2, NATRO%, XLA or SPORT waterborne flooring lacquers for an extremely strong but flexible varnish with excellent clarity and strong chemical and mechanical resistance. Unlike other waterborne floor sealers available this product does not require the addition of an extra crosslinking additive.

If sealing a particularly oily or waxy wood such as tropical hardwoods, use induro® ISO Seal shellac-based sealer.

Floor Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large an area at once as this could lead to a patchy appearance once the stain is dry.

1. Stain should be applied by brush/rag or mohair pad
2. Remove excesses with a clean rag

It is important to remove as much excess floor stain as possible so as not to create a film as this could result in poor adhesion of subsequent coats of floor lacquer.

Stains intended for other uses i.e. decking, fencing, garden furniture etc should not be considered for floors as these will contain water-repelling properties,…

This product is formulated from quality shellacs and alcohol to produce a fast drying floor sealer and primer with excellent clarity. Specifically designed for use on timbers such as tropical hardwoods to seal in and isolate contaminants such as oils and waxes that would cause problems with application, drying and finish of induro® Floor Lacquers.

This product is particularly suitable for use on refurbished flooring, as it will seal any remaining contaminants in the substrate which may cause application, appearance and drying problems.

Use prior to coating with induro XL1 or XL2 flooring lacquers. If a waterborne sealer for non-tropical wood is required, use induro GP Floor Sealer and Primer.

• Pack size: 5L
• Touch dry: 20 minutes @ 18°C
• Recoatable: 90 minutes @ 18°C
• Coats: 1
• Coverage: 40m² per 5 litres dependent upon the size, orientation and surface quality of the substrate

A fully crosslinked single-pack polyurethane clear flooring lacquer with excellent clarity and non-yellowing properties. As induro® XL1 floor lacquer comes fully crosslinked, there are no pot-life limitations. This waterborne self-levelling varnish is ready for use straight from the can and is resistant to abrasion, scuffs and spillage. XL1 has been designed to be used on all solid and engineered wood flooring with light to high traffic. This product is in scope of 2004/42/EC.

Suitable for all internal softwood and hardwood floors in both domestic and commercial environments. XL1 provides extremely strong yet flexible coatings offering outstanding chemical and mechanical resistance. When used with induro® GP Floor Sealer and Primer, excellent clarity and wood-warming can be achieved. 

Use after sealing with induro® GP Floor Sealer and Primer or ISO Floor Sealer and Primer for a strong yet flexible coating. XL1 can however be used without GP Seal. Maintain XL1 with induro® Maintenance products. induro® XLA Anti-Slip topcoat also available.

For a harder wearing varnish, see induro® XL2 Flooring Lacquer - ideal for high traffic commercial environments.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring a varnish will have to be sanded.…

A dead-matt, 0% sheen fully crosslinked single-pack waterborne polyurethane offering enhanced performance compared to other single pack waterborne floor varnishes. As induro® NATRO% comes fully crosslinked, there are no pot-life limitations. 

NATRO gives a natural, unfinished appearance yet is strong and flexible. Outstanding physical and chemical resistance makes induro® NATRO perfect for domestic areas of medium to high traffic. Use coat-on-coat or over induro® GP or EB seal for outstanding clarity and woodwarming. 

Suitable for internal soft and hardwood flooring for domestic applications with medium to high traffic.

induro® is not suitable for areas where high levels of water are present, e.g. bathrooms and swimming pool walkways.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring a varnish will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing varnishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range…

An extremely tough yet flexible fast-drying waterborne polyurethane two pack varnish offering enhanced chemical and mechanical resistance. XL2 is perfect for solid and engineered wood floors with medium to high traffic where high resistance to scuffs, spills and abrasions is required. Noted for its natural clarity, woodwarming and non-yellowing properties. This product is in scope 2004/42/EC.

Use after sealing with induro® GP Seal or ISO Seal for a strong yet flexible varnish. Maintain XL2 with induro® Maintenance products.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring varnishing will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing finishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large an area at once as this…

induro® SPORT is a tough resilient two pack waterborne polyurethane varnish especially formulated to be used on sports floors. Accredited with BS EN 15301 for rotational resistance and BS EN 14904 dry slip resistance, induro® SPORT meets international standards for multi-sport use. Highly resistant to scuffs and marks, SPORT is suitable for other domestic and commercial high traffic areas.

Use after sealing with induro® GP Seal or ISO Seal for a strong yet flexible coating. Maintain SPORT with induro® Maintenance products.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring a varnish will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing finishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large an area at…

XLA ANTI-SLIP is a two pack waterborne polyurethane lacquer that is highly resistant to scuffs, spills and marks. Suitable for domestic and commercial high traffic areas with wooden floors. induro® XLA ANTI-SLIP meets wet slip accreditation BS 7976-2. This varnish is designed to reduce slip potential in bars, clubs, hospitals, schools, shopping centres and all other high-traffic public areas. 

Use after induro® GP Seal / ISO Seal and 2 - 3 coats of induro® XL2 for a strong yet flexible varnish. Maintain SPORT with induro ®Maintenance products.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring varnish will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing finishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large…

These oils are formulated with a blend of urethane and natural oils for use on all types of solid and engineered flooring, such as parquet. They produce a smooth, natural finish with excellent resistance against water and other household liquids. Oiled finishes are easily and quickly maintained with additional coats once tired.

induro® Oil can now be Fastmatch® colour-matched like our original lacquers.

Click here for maintenance products for the induro® range.

• Pack size: 5L
• Dry and re-coat: 3 - 4 hours each for clears, 4 - 6 hours each for pigmented
• Traffic: light - high traffic with good maintenance
• Coverage: 40 - 60m² per 5 litres dependent upon the application method, and absorbency and surface quality of the timber being coated

A quick drying, low odour, high build acid-catalyst lacquer designed for application to wooden flooring by mohair roller, big-foot applicator or T-bar. induro® Acid-Catalyst Flooring Lacquer is available as a clear product in a range of sheens.

induro® Acid-Catalyst Flooring Lacquer will accept light traffic 24 hours after application. Do not place furniture or move furniture across the floor surface for at least 72 hours.

Formulated to provide excellent resistance to abrasion, wet and dry heat, spirit solutions and a wide range of household chemicals. Meets FIRA 6250 Horizontal Surfaces (excluding kitchen worktops) as Heavy/Severe Use.

Substrate Preparation

Virgin substrate

1. Prepare with 120g and 240g sanding paper
2. Completely remove all dust residue prior to application

Pre-coated substrate

1. Strip back to the wood
2. Sand with a series of grits between 36g and 120g using a belt sander
3. Finish sanding with a tri- or monodisc finishing sander

Application Guidelines

1. Use a short mohair or similar roller, mohair flooring pad or T-bar applicator
2. Predominantly with the grain, apply the lacquer evenly, making smooth passes with the roller/pad
3. Apply 3-5 coats at 75-80g/m² per coat wet film thickness (minimum of 4 coats for high traffic areas)
4. Allow 3 hours to dry between coats
5. For best results, only…

Especifically designed to compliment the induro® range of floor coatings. These products are not suitable for areas where high levels of water are present, for example bathrooms and swimming pool walkways.

GP Cleanse

Use with induro® XL1, XL2 and XLO. Dilute with 5 parts water for general cleaning, or use neat for stubborn stains and marks: 

1. moisten a lint-free cloth or mohair pad to wipe the area, turning the cloth or washing the pad as it picks up dirt residue;
2. when all dirt removed (the cloth is clean after wiping the surface), continue to XL Revive or XLO Revive.

XL Revive 10/30 

Use with induro® XL1 and XL2 only. XL Revive is supplied ready for use, thinning is not recommended. For 10% sheen induro® XL1 and XL2 use XL Revive 10, for 30% induro® XL1 and XL2 use XL Revive 30:

1. working with the grain, use a lint free cloth or mohair paid to to evenly apply a thin layer of XL Revive over the whole surface;
2. allow the surface to dry prior to use and ensure no pooling of either product.

XLO Revive

Use with induro® XLO only. induro® XLO Revive is supplied ready for use, thinning is not recommended:

1. working with the grain, use a lint free cloth, mohair pad or, on larger areas a t-bar, to evenly apply a thin layer of XLO Revive…

A cellulose-based binding medium for mixing with sanding dusts to produce a fast-drying filler for use in filling nail holes, splits/shakes and gaps between joints up to 5mm in width/depth.

Overcoatable with induro® XLO oils, and XL1, XL2 and XLA waterborne flooring lacquers.

Mixing Guidelines

1 part binding medium : 1 or 2 parts clean sanding dust (80g - 120g sanding) to produce a smooth paste.

Application Guidelines

Preparation

Flooring should be clean, dry and sanded back to bare timber

Application

1. the filler should be applied over the whole area using a trowel, scraper or other straight edged tool. Ensure that holes, shakes and gaps are completely filled
2. allow to dry
3. sand with 100g - 120g sanding paper
4. repeat if required

• Pack size: 5L and 25L
• Mixing ratio: 1 part binder : 1 or 2 parts sanding dust
• Dry time: 20 - 60 minutes depending on the mixing ratio, amount applied and the ambient conditions

A gloss oil-free moisture-cured polyurethane lacquer for internal wood based floors, suitable for application by brush, roller or T-bar. 

This material has excellent adhesion, abrasion and resistance properties, and will not chip or flake. Supplied ready for use.

Touch dry, sandable and recoatable times are dependant upon temperature, humidity and airflow.

Application

1. remove all traces of previously applied lacquers/waxes
2. sand through with a range of grits, finishing with 120G
3. sweep and vacuum all debris and dust (particularly between boards) from the surface
4. apply the first coat of lacquer at between 6 – 8m² per litre and allow to dry for 3 – 5 hours
5. denib the surface with 120 – 150 mesh screen, sweep and vacuum up dust
6. apply second coat of lacquer at 10 – 12m² per litre
7. if required a third coat can be applied, de-nib with 120 – 150 mesh screen before application

• Touch dry: ~1 hour
• Sandable: 3 – 5 hours
• Recoatable: ~8 hours
• Coverage: 30 - 40m² per 5L dependent upon the type and porosity of the surface
• Coats: 2-3 coats at 10-12m² per litre

induro® UV-curable waterborne varnish for on-site use. The lacquer can be put straight into full service after the final cure of the topcoat, thereby significantly reducing costly downtime. Can be used on floors, bar-tops and other wooden surfaces. Available as a clear product in matt, semi-matt, satin and gloss.

• Extreme chemical and physical resistance
• Self-sealing, no primer or basecoat required
• Easy to apply with roller, t-bar or foam pad

A technically advanced waterborne coating system for wood and parquet floors and flat top surfaces which combines the benefits of the latest developments in raw materials with UV-curing equipment.

Developed and formulated to provide an instant-cure capability after water removal to allow new or refurbished wooden surfaces to be put into use immediately. The potential for damage during a cure period can be eliminated with the use of induro® in-sitUV lacquer.

• Free from NMP, NEP, formaldehyde and isocyanate
• No lingering odour, non-flammable, no pot-life
• 26g/L of VOC

Application

1. Sand the floor, parquet or counter-top back to wood with a mechanical sander using appropriate grits or screens, typically finishing with 120 grit on flooring and 180 grit on counter-tops.

2.  Check and record the moisture content of the substrate in several places taking care to include extremities…